Compression Molding is a method of molding in which the moulding material, generally preheated, is first placed in an open, heated mould cavity. The mold is closed with a top force or plug member, pressure is applied to force the material into contact with all mold areas, while heat and pressure are maintained until the molding material has cured. The process employs thermosetting resins in a partially cured stage, either in the form of granules, putty-like masses, or preforms.
Compression molding is a high-volume, high-pressure method suitable for molding complex, high-strength fiberglass reinforcements. Advanced composite thermoplastics can also be compression molded with unidirectional tapes, woven fabrics, randomly oriented fiber mat or chopped strand. The advantage of compression molding is its ability to mold large, fairly intricate parts. Also, it is one of the lowest cost molding methods compared with other methods such as transfer molding and injection molding; moreover it wastes relatively little material, giving it an advantage when working with expensive compounds.
However, compression molding often provides poor product consistency and difficulty in controlling flashing, and it is not suitable for some types of parts. Fewer knit lines are produced and a smaller amount of fiber-length degradation is noticeable when compared to injection molding. Compression-molding is also suitable for ultra-large basic shape production in sizes beyond the capacity of extrusion techniques. Materials that are typically manufactured through compression molding include: Polyester fiberglass resin systems (SMC/BMC), Torlon, Vespel, Poly(p-phenylene sulfide) (PPS), and many grades of PEEK.
Compression molding was first developed to manufacture composite parts for metal replacement applications, compression molding is typically used to make larger flat or moderately curved parts. This method of molding is greatly used in manufacturing automotive parts such as hoods, fenders, scoops, spoilers, as well as smaller more intricate parts. The material to be molded is positioned in the mold cavity and the heated platens are closed by a hydraulic ram. Bulk molding compound (BMC) or sheet molding compound (SMC), are conformed to the mold form by the applied pressure and heated until the curing reaction occurs. SMC feed material usually is cut to conform to the surface area of the mold. The mold is then cooled and the part removed.
Materials may be loaded into the mold either in the form of pellets or sheet, or the mold may be loaded from a plasticating extruder. Materials are heated above their melting points, formed and cooled. The more evenly the feed material is distributed over the mold surface, the less flow orientation occurs during the compression stage.
Thermoplastic matrices are commonplace in mass production industries. One significant example are automotive applications where the leading technologies are long fibre reinforced thermoplastics (LFT) and glass fiber mat reinforced thermoplastics (GMT).
In compression molding there are six important considerations that an engineer should bear in mind:
- Determining the proper amount of material.
- Determining the minimum amount of energy required to heat the material.
- Determining the minimum time required to heat the material.
- Determining the appropriate heating technique.
- Predicting the required force, to ensure that shot attains the proper shape.
- Designing the mold for rapid cooling after the material has been compressed into the mold.
Video Compression molding
Process definition
Compression molding is a forming process in which a plastic material is placed directly into a heated metal mold, then is softened by the heat, and forced to conform to the shape of the mold as the mold closes.once molding is completed excess Flash are removed, in-order to get best finish.
Maps Compression molding
Process characteristics
The use of thermoset plastic compounds characterizes this molding process from many of the other molding processes. These thermosets can be in either preform or granule shapes. Unlike some of the other processes we find that the materials are usually preheated and measured before molding. This helps to reduce excess flash. Inserts, usually metallic, can also be molded with the plastic. As a side note, remember not to allow any undercuts on the shape, it will make ejection especially difficult. Thermoplastic matrices with an inherent indefinite shelf-life and shorter cycle moulding times are widely used and examples are shown in Ref 3.
Process schematic
Compression molding is one of the oldest manufacturing technique for rubber molding. The process parameters includes molding time, temperature, and pressure. Usually, a 300-400 ton clamp pressure is used. The typical mold is shaped like a clam shell. The molding press looked a lot like a ladle filled vertical press used for casting aluminum. The bottom of the mold was always the cavity. Compression molding used preforms made by an extruder/wink cutter or a roller die/die cutter. Wink meaning that 2 blades meet on center to cut the extrudate to length. For example; Molding water bottles used die cut sheets from a roller die. The sheet was 3 inch by 6 inch. The first sheet was placed- one below a core and one sheet of equal size above the core, and then the top of the mold lowered by hand or by hoist to near shut. The mold was then pushed into the press. The start button hydraulically closed the vertical press to full pressure. The mold temperature was about 350 degrees. The platens of the presses were steam heated. When the cycle ended (about 3.5-4.0 Minutes) the press would open and the mold would be pulled out toward the operator. The operator would pry to open the clam shell mold top, and then lean the top of the mold back against the press. Exposed is the bottle with the core still inside. While the bottle was still hot the operator would insert prongs like reverse pliers in between the bottle rubber and the steel core. The operator would then stretch the bottle at the neck over the core to free the bottle. In preparation of compression molding baby nipples and golf ball centers the preforms were extruded. The baby nipple was a kidney shape about 2 inches tall and 1/2 inch wide in the middle. The golf ball center preform had a 1 x 1 inch round slug. Both slugs were designed to stand up in the mold cavity. During the cycle the operator would load the jig with slugs. When the mold is opened, the lower platen would lower and the mold would be hydraulically pushed ou to the operator. Therein, the heat sheet (all molded parts from that cycle were joined together by a parting line rind (flash)) were placed in a transfer cart. The next cycle began by the jig being put over the mold. The slide tray was pulled and the preforms were released into the cavity of the mold. The start button moved the lower platen back into the press and the cure cycle bagan again. Therein the first cycle was complete. Each operator ran an average of 4 presses. Loading an unload was done during the cycle. The heat sheets removed from the mold were then transported to a die station. The die out station would remove the rind leaving the finished parts. With the evolution of compression molding, next was injection transfer. Basically the extruder was made part of the molding cycle. The rubber was injected into an upper heated platen station, and then pressure was applied to transfer molten rubber to the clamped mold. The design of injection transfer and improved molds were more so plastic injection molding except the platens and molds of injection transfer are heated. In contrast plastic Injections molding shoots a hot plastic into a cold mold.
Workpiece geometry
Setup and equipment
Typical tools and geometry produced
Three types of molds used are the flash plunger-type, straight plunger-type, and the "landed" plunger-type molds. The flash type mold must have an accurate charge of plastic and produces a horizontal flash (excess material protruding from the mold). The straight plunger-type mold allows for some inaccuracy in the charge of plastic and produces a vertical flash. The landed plunger type mold must have an accurate charge of plastic, and no flash is produced. Further details are explained in Ref 3.
See also
- Matrix molding
References
Bibliography
- Todd, Robert H., Dell K. Allen, and Leo Alting. Manufacturing Processes Reference Guide. New York: Industrial P, Incorporated, 1993 on page 219-220....
External links
Source of the article : Wikipedia
0 Comments